November 17, 2026
The Best Way to Clean Block Paving Without Losing Sand
By @marcoonyh123
Block paving is a popular choice for driveways, patios and paths across Ipswich, and it's easy to see why. It's durable, attractive and relatively simple to repair. But anyone who has cleaned a block-paved surface knows the risk: blast it with the wrong equipment and you can strip out the jointing https://angeloeegr000.nexorafield.com/posts/why-preventive-exterior-care-beats-emergency-cleaning sand that holds the whole surface together. Once that sand disappears, blocks start to shift, weeds move in, and water can wash away the sub-base beneath. The good news is that you can get your paving looking fresh while keeping the sand where it belongs.
Why Jointing Sand Matters
The sand between your blocks isn't just cosmetic. It locks the blocks together, allowing them to share loads from cars and foot traffic. It also helps prevent weed growth, limits water penetration and keeps the individual blocks from rubbing against each other and chipping at the edges.
Traditional kiln-dried sand is soft and easily displaced. Polymeric sand, which hardens when activated by moisture, is much more resistant to washing out, but even this can be damaged by aggressive cleaning, particularly if it has aged or was poorly installed.
Why Pressure Washing Strips Sand
The main culprit is a standard pressure washer used with a straight, narrow jet held close to the surface. High-pressure water drives straight into the joints and flushes the sand out, sometimes to a depth of several centimetres. Many homeowners in Ipswich don't notice the damage until after the surface has dried and the joints look hollow.
Ipswich's climate adds to the challenge. With mild, damp conditions typical of Suffolk, moss, algae and lichen build up readily on shaded driveways and north-facing patios. That tempts people to reach for the strongest pressure setting, which is exactly what causes the problem.
The Best Approach: Step by Step
The safest method combines gentle pre-treatment, controlled washing and proper re-sanding. Here's how to do it.
- Clear the surface. Sweep away loose debris, leaves and surface dirt with a stiff brush. Remove any large weeds by hand or with a weeding knife.
- Apply a biocidal treatment. Use a moss and algae killer designed for hard surfaces. Apply it on a dry day and leave it to work for the time stated on the label. Often the organic growth will begin to die back and loosen without any force at all.
- Wash at lower pressure. Use a pressure washer on a low setting, typically below 1,500 psi, with a wide fan nozzle (25 to 40 degrees). Keep the lance at least 30 cm from the surface and work at an angle rather than pointing straight down into the joints.
- Use a surface cleaner if possible. A rotary surface cleaning attachment keeps the spray contained and at a consistent height, which reduces the chance of blasting out joints.
- Let the surface dry fully. Allow at least 24 to 48 hours, depending on the weather, before assessing the joints.
- Top up the jointing sand. Sweep fresh sand across the dry surface, working it into every gap. Compact lightly if needed and sweep off any excess.
Alternatives to Pressure Washing
Stiff Brush and Detergent
For small areas or lightly soiled paving, a stiff-bristled broom and a patio-safe cleaner can be surprisingly effective. It takes more effort, but it places almost no stress on the joints.
Soft Washing
Soft washing uses low pressure combined with cleaning solutions to break down algae, moss and grime. It's widely used on delicate surfaces and is a good option for block paving that is already in fragile condition. Many professional cleaners in the Ipswich area now offer this as a standard service.
Steam or Hot Water Cleaning
Hot water systems can lift grease, chewing gum and oil stains without relying on heavy pressure. They are useful for spot treatment, though they still need to be used carefully near joints.
Choosing the Right Sand for Re-Sanding
After cleaning, replacing the jointing material is essential. Your main options are:
- Kiln-dried sand: Cheap and easy to apply, but can wash out again over time and may allow weed growth.
- Polymeric sand: Hardens when dampened, resists weeds and ants, and holds up much better against rain and cleaning. It's generally the better long-term choice for driveways.
- Resin-bound jointing compounds: A premium option that creates a very firm joint, although it can be harder to repair later.
When applying polymeric sand, the paving must be completely dry, and the product must be activated with a light mist of water as instructed. Applying it to damp blocks or leaving residue on the surface can leave a hazy film that is hard to remove.
Common Mistakes to Avoid
Using a zero-degree nozzle: The pinpoint jet is designed for stubborn stains on concrete, not for block paving.
Cleaning too often: Washing once or twice a year is usually enough. Over-cleaning gradually erodes joints.


Skipping the sealant decision: Sealing can protect colour and help lock in sand, but it should only be applied to clean, dry paving with fully filled joints. Make sure you choose a breathable, block paving-specific product.

Ignoring drainage: Standing water encourages algae and washes out sand. If water pools on your driveway, there may be an underlying levelling or drainage issue that needs addressing.
Environmental and Local Considerations in 2026
Runoff from cleaning chemicals should not enter surface water drains, which discharge to local watercourses. Where possible, direct wash water onto a lawn or soakaway area, choose biodegradable cleaners, and avoid treating paving ahead of heavy rain. Professional cleaners are increasingly expected to capture and dispose of wastewater responsibly, so it's worth asking about their methods if you hire someone.
When to Call a Professional
If your driveway has deep staining, extensive moss growth, sunken blocks or joints that have already washed out badly, a professional assessment is worthwhile. A reputable Ipswich paving specialist can clean the surface using controlled equipment, re-sand it correctly and advise whether sealing or repairs are needed. It often costs less than correcting damage from an overly aggressive DIY clean.
Final Thoughts
Cleaning block paving without losing sand comes down to using the right tools, keeping pressure low and always finishing with fresh jointing material. Treat moss and algae chemically first, wash gently, let the surface dry, then re-sand properly. Done correctly, you'll restore the look of your paving and protect its structure for years to come, whether you're maintaining a driveway in Ipswich town centre or a patio in the surrounding Suffolk villages.
Ipswich Pressure Cleaning Pros
(07) 3278 0498
❧